Xhorse VVDI BIM Tool BIMTool Pro Updated Version of VVDI BMW

 

VVDI BIM TOOL  Pro Using Notice

1. Notice Do not use the Internet Port and USB Port at the same time:
For FEM/BDC Program using the USB Port connect is ok.
For Others Program you can connect the Internet Port .

2. When connect the Port with PC, first it display"Booting", after about 20 seconds it will display"BMW"
then the connect is ok.

Xhorse VVDI BIM PRO VS VVDI BMW  VS VVDI2 BMW:
 

	VVDI BIM PRO	VVDI BMW	VVDI2 BMW
Color	Blue	Blue	Yellow
Functions	Locksmith,programming,coding	Locksmith,programming,coding	Locksmith
Update	Software Online for free Firmware use "update kit" update for free	Software Online for free Firmware use "update kit" update for free	Software Online for free Firmware use "update kit" update for free
Support System	EWS to CAS (1, 2, 3, 3++ 4, 4+) and the latest FEM/ BDC system	EWS to CAS (1, 2, 3, 3++ 4, 4+) and the latest FEM / BDC system	EWS to CAS (1, 2, 3, 3++ 4, 4+)
Programming Funtion	Support Can and DOIP	Support Can	/

Xhorse VVDIBIM PRO vs VVDI BMW

Item	VVDI BIMTOOL Pro	VVDI BMW TOOL
Remark	In stock	Out of stock
Language	Chinese, English,   Italian, Spanish, German, Hungarian,  Polish	Chinese, English, Italian, Spanish,  German, Hungarian, Polish
Program E/F chassis	Yes	Yes
Code E/F chassis	Yes	Yes
Learn OBD key	Yes for CAS1 / CAS2 / CAS3 / CAS3+ / CAS3+ ISTAP / CAS4 / CAS4+	Yes for CAS1 CAS2 CAS3 CAS3+  CAS3+ISTAP CAS4 CAS4+
File make key	Yes for CAS1 CAS2 CAS3 CAS3+  ISTAP CAS4 CAS4+, etc.	Yes for CAS1 CAS2 CAS3 CAS3+  ISTAP CAS4 CAS4+, etc.
Gnerate key for FEM/BDC system	Yes	Yes
Correct mileage	Yes for CAS1 CAS2 CAS3 CAS3+ ISTAP CAS4 CAS4+ and FEM / BDC system	Yes for CAS1 CAS2 CAS3 CAS3+  ISTAP CAS4 CAS4+ and FEM/BDC system
Read EEPROM & synchronous code data	Yes for CAS1 CAS2 CAS3 CAS3+	Yes For CAS1 CAS2 CAS3 CAS3+
Get ECU ISN	Yes	Yes
Support synchronous ECU and CAS,  synchronous ELV and CAS	Yes	Yes
Reset 8HP gearbox in F chassis	Yes	Yes
Exchange ECU and CAS	Yes	Yes
Add ethernet port	Yes, support 10/100M programming via Ethernet	No
WiFi	Yes, support WIFI 802.1b/g,  150Mbps high-speed connection,  and WIFI OTA upgrade	No
DoIP Vehicle/Module Programming	Yes	No
BMW ECU programming (NBT/CIC)	Yes,  connect via network cable	No
Speed up the F/G Chassis programming	Yes, connect via network cable	No
BMW E-sys and Rheingold Diagnostic System	Yes,  able to replace the specialized devices (connect via network cable)	No
Read N13/N20/N55/N63 ISN data without disassembling	Yes	No

VVDI BIMTOOL Pro Tool Faq:

A:I received the package but Xhorse VVDI BIMTool Pro doesn’t work. There was no connection with the car (either via CAN or KLINE bus). I updated the device to the newest software and firmware. any iead?
Q:you should  short the component in the following printed circuit board with a zero-ohm resistor below picture